A NAS or RAID server rarely fails without warning. More often the hardware sends signals days, weeks or even months ahead: a SMART attribute that changes, a slowdown, a drive that vanishes and comes back. They are easy to miss because the service keeps running thanks to redundancy. This article covers the symptoms worth watching, what they can mean, and the most cautious response, without claiming that any single sign means a failure is certain.

Why the signals stay quiet with RAID

RAID is designed to hide the failure of a drive: the volume stays accessible, users notice nothing, and the first trace of a problem may be a line in a log or an email nobody reads. That is what makes observation valuable. Once a volume is running in degraded mode, it is no longer an early warning but a failure; that moment is covered in our article on a beeping NAS. Here, the focus is on what comes before. A drive can show several symptoms at once, or none before it gives up: monitoring remains useful without being infallible, and it does not replace an up-to-date backup.

SMART alerts and reallocated sectors

SMART is a self-monitoring system built into drives. A NAS or server interface shows an overall health status and, depending on the model, the detail of each attribute. Five attributes are regularly cited: reallocated sectors (no. 5), reported uncorrectable errors (no. 187), command timeouts (no. 188), pending sectors (no. 197) and uncorrectable sectors (no. 198).

In its fleet analysis, Backblaze found that at least one of these five attributes was above zero on 76.7% of failed drives, against 4.2% of drives still in service. The signal is clear but not absolute: 23.3% of failed drives had shown nothing. Backblaze also notes that an isolated non-zero value says little, that the repetition of errors should be examined, and that most of these counters are cumulative, so what matters is how they progress over time.

A Google study of a large drive population points the same way. Fewer than 2% of drives showed scan errors, but those drives failed about ten times more often, and after the first scan error the probability of failure within 60 days was 39 times higher. Drives with reallocated sectors failed 3 to 6 times more often. The authors also note that many failed drives had shown none of these signals: the absence of an alert is not a guarantee.

In practice: enable the NAS email alerts, schedule SMART tests, and note the values of these attributes from time to time so that any change can be spotted.

Noises, slowdowns and unusual behaviour

Noises

Every machine has its background sound: fans, spinning platters, moving heads. What should raise concern is a change: repeated clicking, banging, grinding, or a new noise during a large copy. Clicking points more towards a mechanical problem. The safest course is then to limit the use of the drive concerned, since continuing to stress it can make the damage worse.

Slowdowns

Shared folders that open slowly, or throughput that stays below what it was in the first months, deserve attention. A drive struggling to re-read certain sectors can slow down the whole array. A slowdown can also have an ordinary cause (a backup or indexing in progress, a saturated network): comparing it with a reference speed recorded when everything was fine settles the question.

Restarts and crashes

An unexpected restart, an application or virtual machine that crashes, a file system reporting errors: these symptoms have varied causes (power supply, memory, firmware, drive). They do not point to a particular drive, but if they recur, the system logs often show what precedes the incident.

A drive that leaves the array, then comes back

A drive reported missing or disconnected, then reintegrated on its own, may come from a poor contact in the bay or from a drive that responds less and less reliably. This episode is not a closed incident: note the date, the bay and the serial number, and treat that drive as suspect. An automatic resynchronisation is not a repair.

LEDs and alarms

An LED that changes colour, a notification or a beep is the next stage. The hardware is then reporting a state that is already degraded, covered in the article mentioned above.

Temperatures

A rising temperature can come from dust, a weakening fan or a poorly ventilated room. The Google study found little link between temperature and failures in the moderate ranges, with an effect only at the high end and mostly on older drives. Temperature alone therefore does not predict a failure, but lasting heat points to a ventilation problem that should be fixed, and it is best to stay within the range given by the manufacturer.

Reading the signals together

A single signal is an observation. Several signals converging (a SMART attribute that keeps rising, a slowdown and a drive that left the array) are a good reason to act without waiting, all the more so because each of these signs can be observed without specialist tools, from the NAS interface or its logs. The diagram below summarises the main symptoms, what they can mean and the recommended response.

Three-column table titled symptom, possible meaning, recommended response. Rows: SMART alert or rising reallocated sectors, a drive that is wearing out, check the backup and plan a replacement; clicking or a new noise, possible mechanical problem, limit use and prepare a copy; lasting slowdown, a struggling drive or an outside cause, compare with the reference speed and check the logs; repeated restarts or crashes, hardware or software cause, collect the logs; drive that left then came back, poor contact or suspect drive, note it and monitor it; rising temperature, insufficient ventilation, clean and check the fans.

What to do when a sign appears

  • Document it. Note the date, the exact message, the drive and bay concerned, and take a screenshot of the interface.
  • Check the backup. Is it recent, and have you ever tried restoring a file from it? The 3-2-1 rule, restated by CISA, calls for three copies on two types of media, one of them kept off site. RAID does not replace this, as our article on why RAID is not a backup explains.
  • Copy the essentials first. Secure the critical data on an external medium before touching the array.
  • Do not force a rebuild. Replacing a drive and starting a rebuild makes every other drive be read in full. If one of them is already fragile, the operation can fail. The precautions are detailed in our article on RAID rebuilds.
  • Plan the replacement. Once the backup is secured, replacing a suspect drive at a time of your choosing is better than suffering a failure.
  • Power off if needed. In case of mechanical noise, an inaccessible volume or several faulty drives, shut down cleanly, label each drive with its original bay, and attempt nothing more.

Setting up simple monitoring

  • Enable email notifications in the administration interface, sent to an address that is actually read.
  • Schedule regular SMART tests, both quick and extended, and check the results.
  • Record a reference throughput once, and the machine’s usual noise, to have a point of comparison.
  • Dust the grilles and check that the fans spin, at regular intervals.
  • Test restoring a file from the backup now and then: a backup that has never been restored remains an assumption.

These steps take little time, need no special tool, and turn weak signals into usable information.

The timeline of a degradation and the right moment to act

An array rarely changes all at once. Durations vary widely with the drives, the workload and the environment, but the sequence is often the same: normal operation, weak signals (SMART attributes, slowdowns), a suspect drive or one that left the array, a degraded volume, then a second fault that makes the volume inaccessible. The first two stages leave the most room: this is the time to check the backup and replace a drive in a planned way. From the degraded volume onwards, the priority becomes backing up before any rebuild. Once the volume is inaccessible, it is better to attempt nothing more.

Horizontal timeline of a RAID array degrading in five stages: normal operation, weak signals (SMART, slowdowns), suspect drive or drive that left the array, degraded volume, volume inaccessible after a second fault. A green zone over the first two stages marks the right time to check the backup and replace a drive in a planned way, an orange zone over the degraded volume says back up before any rebuild, a red zone over the last stage says attempt nothing more and contact a laboratory.

When to contact a laboratory

Specialist advice is called for when a drive makes a mechanical noise, when more drives are faulty than the RAID level tolerates, when the volume no longer mounts, when a rebuild has failed, or when the data is critical and has no copy. In a laboratory, the approach is to make images of the drives and then reconstruct the array from those images, without depending on the original enclosure or stressing fragile drives further. The outcome depends on the condition of the media, and only a diagnosis can tell. Depending on your hardware, the NAS servers and RAID servers pages describe how cases are handled.

Spotting these signs early leaves time to act calmly: a verified backup, a drive replaced in a planned way, and a failure that remains a minor inconvenience.